Pneumatic Series REN23

Gives a maintained output signal when both buttons are pressed within .3 seconds and held. Working pressure range 60-100 PSI, 40 Micron Filtered Dry Nonlubricated air. Complete two-hand no-tie-down control with buttons on ends.

 

• Compact design with 1-3/8" diameter push buttons   (recessed).
• Light actuation pressure (5 ounces).
• 1/4" push lock fittings included.
• Rounded edges, no sharp edges or corners to

  injure operator.
• Quick and simple installation, bolt the control down   and plug in.


Pneumatic Series REN28

Set of 2 palm buttons with logic, two-hand no-tie-down control. Working pressure range 60-100 psi, 40 micron filtered dry nonlubricated. One palm button gives a maintained output signal when both buttons are pressed within .3 seconds and held.

 

• Compact design with 1-3/8" push buttons (recessed   1/4").
• Mounts vertically or horizontally, no mounting   bracket required.
• Light actuation pressure (5 ounces).
• mounting screws included (10-32).
• 1/8" npt connections. 5/32 (4mm) push lock fittings   optional.
• Rounded edges, no sharp edges or corners to

  injure operator.


Pneumatic Series REN300

Complete two-hand no-tie-down. Working pressure range 60-100 psi, 40 micron filtered dry nonlubricated air. Gives a maintained output signal when both
Buttons are pressed within .3 seconds and held

 

• Compact design with 1-3/8" diameter push buttons   (recessed 1/4") on top
• Light actuation pressure (5 ounces).
• Mounting screws included (10-32).
• 1/4" push lock connections standard, 5/32 (4mm)   push lock optional.
• Rounded edges, no sharp edges or corners to

  injure operator.
• Quick and simple installation, bolt the control down   and plug your tubing into the 5/32" 4mm) push lock   connections.

 

Pneumatic Series REN-CC-1004A

The clamp circuit is used with a 2-hand control, end of stroke sensor (-eoss) to latch the circuit on, a release button or an optional timer to release. All are pneumatic. This allows an air cylinder to remain clamped after the operator removes hands from the 2-hand control. The work piece thickness may vary as the end of stroke sensor detects when the cylinder stops.

 

Typical operation: operator presses the 2 green buttons on the 2-hand control, the cylinder advances and clamps on to the work piece, a signal is sent to the clamp circuit to latch on. Hands may be removed from the 2-hand control. The release button or an optional timer is used to release.

 

Electric Series REN46


With top mounted photoelectric sensors. Gives a maintained output signal when both light beams are broken within .3 seconds and held.

 

• Insert fingers to break light beams, no pressure   required
• Compact design with guarded finger slots.
• Input and output cords included.
• Quick and simple installation, bolt the control down   and plug in
• No output if control powered up with beams broken.
• 120v ac input and output. Other configurations are   available


 



 

Electric Series REN44

With push buttons. Gives a maintained output signal when both buttons are pressed within .3 seconds and held.

 

• Compact design with 1 3/8" diameter push buttons   (recessed).
• Light actuation pressure.
• Input and output cord included.
• Rounded edges, no sharp edges or corners to
  injure operator.
• Quick and simple installation, bolt the control down   and plug in.
• No output if control powered up with buttons   pushed.

• 120v ac input and output. Other   configurations   available

Electric Series REN45

With photoelectric sensors. Gives a maintained output signal when both light beams are broken within .3 seconds and held. Insert fingers to break light beams, no pressure required.


• Compact design with 1" diameter finger holes.
• Input and output cords included.
• Rounded edges, no sharp edges or corners to

  injure operator.
• Quick and simple installation, bolt the control down   and plug in.
• No output if control powered up with beams broken.
• 120v ac input and output. Other configurations   available.


CFA Contact Information

  • emailEmail
    sales@gocfa.com
    marketing@gocfa.com
  • phonePhone
    800-323-3164 (toll free)
    508-802-6005
    508-8026006 (fax)
  • addressAddress
    Controls For Automation, Inc.
    25 Constitution Drive, Taunton,MA 02780
  • Our business hours:
    Monday - Friday: 8:00am - 5:00pm (EST)

Visit RENCO CONTROLS official website:
http://www.rencocontrols.com